colonyroll1

How to Replace a Saab 9-3 Key The Saab 9-3 is a car that has a large deal of appeal for drivers. saab 9-3 key replacement has a powerful engine as well as good visibility. It also has a top safety rating. It is nevertheless important to make sure that you have at the very least two keys that work for your car. If you lose only one key, it could be very costly to buy a new one. How to Replace the Ignition Key in the Saab9-3 If your car's key doesn't turn in the ignition, you need to replace it. This guide will guide you through the steps to do it on a Saab 9-3. You will need a replacement key, a new reprogrammable battery as well as a new key-fob cover. Modern Saab models make use of a transponder instead of a key made of metal to unlock the car and then start it. The rechargeable batteries contained in the key-fob expire, and they can't hold any charge. This is especially when you use the same key for the same lock. The good news is that the battery can be replaced quite easily by an experienced locksmith. You can also do it yourself if you have the proper tools and a bit of patience. The first step is to disassemble the key-fob from its case. This is accomplished by inserting a flathead screwdriver into the slot located in the middle of the case. The plastic is thin, and can easily be damaged. After the case has been opened then you can prepare the new key by combining the lower part of the previous key with the transponder and banana on the new key. This will ensure the new key is properly connected to your CIM, which can be a major difference when replacing the sole key for your Saab 9-3. How do I replace the ignition Key on the Saab 900 Unless you have two keys, you'll have to take off the dashboard and steering wheel to gain access to the ignition. Start by disconnecting the negative battery cable. After the battery has been disconnected, you can remove the dashboard and trim pieces around the steering wheel. Once the dash has been taken off, you can push an screwdriver through the hole behind the ignition switch and take it out. The ignition cylinder is equipped with the key lock, which can stop the vehicle from starting if the key isn't in it. If the ignition switch on your 900 doesn't work correctly, make sure to check whether the key is in the lock or snared inside the ignition barrel. It's also a good idea to rotate your keys on a regular basis and clean them regularly so that one doesn't get bent. Saab cars differ from other vehicles because they don't use traditional metal keys. Instead, the car is able to recognize the key fob's electric signals by a specific chip inside it. If you lose your only working key fob the dealer will charge you the highest dollar for replacing the computer module (known as the CIM). We can reprogram the EEPROM of your existing computer and allow it to accept new keys without having to replace it. This can save you over 50% of the cost the dealer charges! We call it the SAAB Key PROGRAM. Find out more here! How to Replace the Ignition Key in the Saab9-5 The metal part of the classic Saab keys is simple to duplicate and doesn't present a major threat to theft of vehicles. The real protection comes from the electronic part in the key-fob, which is equipped with a chip that can recognize your vehicle when it is inserted into the ignition switch. Saab has relied on the technology of this anti-theft system for over 10 years. It's not as efficient as a door lock, but it makes stealing your car much more difficult. Every Saab owner needs to keep an extra Saab key in their car. The majority of new Saabs are delivered with two keys, however they can be added by an dealer by using a handheld device, called Tech-2. Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception to this is NG 9-3 cars, which are equipped with modernized, more modern features that require a different key-fob and use a different method of operation. If you lose all keys in the event of a loss, the dealer will replace your CIM or TWICE modules, and charge you the cost of replacement. We can reprogram your computer's EEPROM to accept new keys without having to replace expensive modules. How to replace the ignition Key in an XC90 Saab It's probably time to replace your SAAB key fob if it is having trouble turning the lock barrel. The process is simple and you don't have to visit a dealership. Instead you can complete the process yourself at home with the help of a few tools. First, you'll need prepare the new key. Before you begin, turn off the anti-theft system by placing blocks under your rear wheels and engaging your handbrake. Insert the key in the ignition and turn it to the “on” position. This will activate the accessories, but not start the engine. Repeat this procedure 5 times, and then leave the key on the “on” position. Next, you'll need to find a new case for your old key fob. They are readily available at many auto parts stores and are generally inexpensive. You can buy them with or without electronics, depending on the model. To open the case you need to gently push the screwdriver with a flathead into the slot in the middle. After you have split the case, you'll have access to all the internal electronic components. To remove the electronics, use a small screwdriver and try to pry them out with a gentle force.